<p>Deprem performansı yetersiz olan yapıların, ekonomik ve güvenli olması koşuluyla, güçlendirilmesi meydana gelebilecek can ve mal kaybını azaltmak için önem taşımaktadır. Güçlendirme, elemanın mevcut taşıma kapasitesini, elemanın yetersiz olduğu özellikleri (kesme, eğilme vb.) doğrultusunda gidererek arttırma işlemidir. Bu kapsamda betonarme elemanın dıştan sargılama (EBR) ve/veya yüzeye yakın montaj (NSM) yöntemiyle güçlendirildikten sonraki moment taşıma kapasitesinin tasarım aşamasında hesaplanarak etkin güçlendirme detaylarının belirlenmesi gerekmektedir. Taşıma gücü hesabında yapılan kabullerden biri de kesitin taşıdığı beton basınç kuvveti hesabında betonun gerçek gerilme dağılımı yerine eşdeğer dikdörtgen basınç bloğunun kullanılmasıdır. Çalışma kapsamında literatürde bulunan deney numunelerinin moment kapasiteleri analitik olarak hesaplanmıştır. Kesitin taşıma gücü hesabında betonun gerilme-şekildeğiştirme eğrileri önce parabolik daha sonra eşdeğer dikdörtgen basınç bloğu olarak etkitilmiştir. Beton basınç bloğunun parabolik olduğu durumda beton basınç kuvveti, lifli yönteme göre belirlenmiştir. Hesaplamalarda TRM sargının beton basınç dayanımına etkisiyle birlikte CFRP levhaların kesitin moment kapasitesine etkileri dikkate alınarak numunelerin moment taşıma kapasiteleri elde edilmiş ve deney sonuçlarıyla kıyaslanmıştır. Çalışma sonucunda her iki yönteme göre hesaplanan moment taşıma kapasiteleri, deneysel sonuçlarla uyumlu elde edilmiştir. Eşdeğer dikdörtgen basınç bloğuna göre hesaplanan moment taşıma kapasiteleri, deneysel sonuçlarla daha az uyumlu ve parabolik basınç bloğuna göre belirlenen kapasitelerden %1.44 ile %3.48 oranlarında daha düşüktür. Herhangi bir güçlendirmenin uygulanmadığı, yalnızca NSM yöntemiyle ya da NSM ve EBR yöntemlerinin beraber uygulandığı yöntemle güçlendirilen betonarme elemanlarda beton gerilme dağılımı her iki şekilde kullanılarak lifli ya da eşdeğer dikdörtgen basınç bloğu yöntemlerine göre moment taşıma kapasiteleri belirlenebilmektedir. </p>
<p>Strengthening structures with inadequate seismic performance, provided that they are economical and safe, is important to reduce the loss of life and property that may occur. Strengthening is the process of increasing the existing bearing capacity of the element by eliminating the inadequate features of the element (shear, bending, etc.). In this context, the moment bearing capacity of the reinforced concrete element after it is strengthened with external wrapping (EBR) and/or nerar surface mounting (NSM) method should be calculated at the design stage and effective reinforcement details should be determined. One of the assumptions made in the bearing capacity calculation is the use of an equivalent rectangular compression block instead of the actual stress distribution of concrete in the calculation of the concrete compressive force carried by the section. Within the scope of the study, moment capacities of the test specimens available in the literature were analytically calculated. In the calculation of the bearing capacity of the section, the stress-strain curves of the concrete were first parabolic and then as an equivalent rectangular compression block. When the concrete compression block was parabolic, the concrete compressive force was determined according to the fiber method. In the calculations, the moment bearing capacities of the specimens were obtained and compared with the experimental results by taking into account the effect of TRM wrapped on the concrete compressive strength and the effect of CFRP plates on the moment capacity of the section. As a result of the study, the moment bearing capacities calculated according to both methods were obtained in accordance with the experimental results. The moment bearing capacities calculated according to the equivalent rectangular compression block are less compatible with the experimental results and are 1.44% to 3.48% lower than the capacities determined according to the parabolic compression block. In reinforced concrete elements strengthened with only the NSM method or with the combined application of NSM and EBR methods, where no reinforcement is applied, the concrete stress distribution can be used in both ways to determine the moment carrying capacities according to the fibrous or equivalent rectangular compression block methods.</p>